WH-01 Surface
Wellhead and metering
This example places flow measurement at the wellhead, with optional line-pressure sensing according to the project scope.
- Flow
- 42.8 m³/h
- Line pressure
- 3.14 bar
Water & well intelligence
From one well to a whole network in view.
Monitor water production, pumping activity, quotas and quality trends. Arddata gives well owners a clear mobile view and operators a shared picture across participating wells.
- For the well owner
- Mobile portal
- For the operator
- Multi-well dashboard
- Core visibility
- Production · quotas · quality
The product in use
Start with the well. See across the network.
For the well owner
A clear mobile overview, with dedicated production and quality views. Follow the current pumping session and quota use without searching through multiple dashboards.
For the multi-well operator
A shared view of participating wells: pumping status, flow, production and quota use. Move from network totals to the well that needs attention.
Arddata™Water intelligenceWell 01Pumping
Current flow rate
107.2m³/h
- Last Hour
- 105m³
- Last 24h
- 2,290m³
- Total
- 51,439m³
- TDS
- 336.7ppm
Current billing cycleWithin quota
Pumped6,342m³
Contract quantity86,400m³
Production progress7%
Miyahuna · shared visibility across participating wells
Arddata brings production data from connected meters into pumping-session records and shared production and quota views for operators. Well owners have a dedicated portal to follow their own well.
From meter to well
Follow the measurement down to its source.
Descend from the instrumented wellhead, past the casing and the water table, to the submersible pump at the base of the borehole.
Wellhead and metering
WH-01 · Surface
This example places flow measurement at the wellhead, with optional line-pressure sensing according to the project scope.
- Flow: 42.8 m³/h
- Line pressure: 3.14 bar
Pending approval
Telemetry and power
GW-02 · Surface
A gateway collects compatible instrument data. Connectivity and power are selected for coverage and conditions at the site.
- Uplink: LoRaWAN
- Signal: −78 dBm
Pending approval
Storage, treatment and distribution
TK-03 · Surface
Storage and downstream measurement points can be included in the monitoring scope where suitable instruments are installed.
- Tank level: 76.2%
- Conductivity: 1.28 mS/cm
Pending approval
Casing and riser column
CS-07 · 50 m
The casing and riser show the physical path of the water. The readings shown do not establish the structural condition of the well.
- Casing: DN 200 · example
- Drop pipe: DN 100
Pending approval
Water table and drawdown
WL-11 · 100 m
Where a level sensor is installed, changes during pumping and recovery can be tracked. Aquifer performance requires qualified interpretation.
- Static level: −100 m
- Drawdown: 12 m
Pending approval
Submersible pump
P-07 · 150 m
Pump electrical and operating measurements can be added using compatible instrumentation. These measurements are not included in every installation.
- Motor current: 18.4 A
- Speed: 2,940 RPM
Pending approval
Illustrative engineering cross-section. Depths and readings are examples; equipment is scoped for each project.
Data & measurements
Measurements with an operational context.
Available measurements and update frequency depend on the equipment, connectivity and configuration at each site.
01
Flow & volume
Current flow, cumulative meter readings and production by hour, day and month from the connected meter.
02
Pumping sessions
Follow periods of activity, duration, produced volume and average flow within each session.
03
Quality trends
Follow TDS or conductivity where sensors are installed, and review changes over time.
04
Quotas & billing cycles
Compare production with the configured cycle quota and review remaining volume and projections where quotas are set up.
05
Device status
Review the last received data and available device information to identify sites needing attention.
06
Additional instrumentation
Level, pressure or pump measurements can be scoped for the project. Remote control requires suitable equipment and a separate control design.
Views for each role
A shared record. The right view for each team.
Access is organized around the organization, workspace and participating wells.
01
Well owner
Production, quality, pumping activity and quota use in a clear mobile portal.
02
Network operator
Compare wells, pumping status and aggregated production in one dashboard.
03
Operations team
Review production history, sessions and quality trends to decide what needs investigation.
04
Reporting teams
Review participating-well production and quota use across billing cycles.
Let’s talk about your project
Plan your next deployment.
Tell us what you operate, what is already on site and what you need to understand. We’ll help define the equipment, connectivity and software your project needs.